News Center

News Center

The difference between a full-spectrum direct-reading spectrometer and a conventional spectrometer!

发布时间: 2022-10-10 09:47

Different types of Spectrometer There are different application areas, so… Full-spectrum direct-reading spectrometer So how does it differ from a conventional spectrometer? Let’s discuss this next!

PMT photomultiplier tubes (vacuum‑type) are used for point‑ or line‑scan measurements and can only detect discrete spectral lines. Each detector element corresponds to a single PMT, so each element must be equipped with at least one tube. Spectral lines are detected at a single wavelength and cannot be acquired continuously. The selection of spectral lines is severely constrained. The more elements to be analyzed, the more PMTs are required. In practice, it is virtually impossible to add additional analytical matrices to a PMT‑based spectrometer after installation; even if matrix addition is feasible, it is typically limited to one or two matrices, and the performance gains are minimal due to physical space constraints.

CCDs (charge-coupled devices) perform area‑scanning (strip‑type) measurements and require deep cooling to enhance the signal‑to‑noise ratio, yet their numbers are far fewer than those of PMTs. Three CCDs—divided into three segments or regions—can cover most elements across the full spectrum, with analytical lines selectable as needed; in particular, the principle of having multiple characteristic lines for a single element allows users to choose several lines for analysis. This facilitates the addition of new channels later on and enables the easy expansion of both matrix types and the range of elements that can be analyzed. Compared with traditional channel‑type instruments based on PMTs, CCD‑based systems offer greater flexibility. If users later wish to add new elemental analyses, they need only introduce the corresponding analytical routines without modifying the instrument’s hardware, making upgrades highly convenient. Moreover, compared with photomultiplier tubes, CCD‑based systems have lower long‑term technical costs.

PMTs are often used for ultra‑high‑precision analyses at extremely low concentrations. Manufacturers frequently tout the size of the tube diameter, but this is a relative measure. Due to the dimensions of the analytical optical chamber, manufacturers typically opt for PMTs to balance design considerations and cost, rather than adhering to the misconception—promoted by some vendors—that a larger tube diameter necessarily translates into better analytical accuracy.

The CCD is a full-spectrum direct‑read detector, capable of acquiring all spectral lines of every element across the designed wavelength range. The advantage of this approach is that, since each element emits distinct characteristic spectral lines at different concentrations, the CCD can simultaneously collect and analyze all these lines. By contrast, when using a PMT, if the concentration range of the analyte spans a wide interval, multiple PMTs must be configured to cover the relevant wavelengths. In practice, however, for cost‑effectiveness, instrument manufacturers typically equip the system only with the PMTs required for the user’s specified analysis range; subsequent upgrades are often necessary (a consideration that depends on the specific application). This is precisely where the CCD outperforms the PMT.

As production processes are refined, each manufacturer develops unique manufacturing techniques that are reflected in the chemical composition. There are two common approaches: adding specific alloying elements or extending the working analytical calibration curve. In subsequent upgrades, CCD‑based instruments—being full‑spectrum direct‑read spectrometers—offer a significant advantage over PMT‑based direct‑read spectrometers, which rely on characteristic spectral lines.

The above is an overview of the differences between a full-spectrum direct-reading spectrometer and a conventional spectrometer. If you would like to learn more, please continue browsing our… Spectrometer Information Section For product information, please contact us!

Latest News

Recommended Products

RoHS 2.0 Rapid Screening Instrument PY-GCMS3080

This page provides information, including frequently asked questions, about the RoHS 2.0 rapid screening instrument PY‑GCMS3080. For pricing inquiries, please contact us online or call our hotline at 19926823034!

Learn more+

RoHS 2.0 Rapid Screening Instrument PY-GCMS3080

RoHS 1.0 Rapid Testing Instrument DX-320L Pro

This page provides an introduction to the DX-320L Pro, a high-performance desktop XRF analyzer compliant with RoHS 1.0. For more information, please contact 19926823034.

Learn more+

RoHS 1.0 Rapid Testing Instrument DX-320L Pro

RoHS 1.0 Detector – IDP8300L Fluorescence Spectrometer

This page provides specifications and FAQs for the DP8300L fluorescence spectrometer. For pricing inquiries, please contact us online or call 19926823034!

Learn more+

RoHS 1.0 Detector – IDP8300L Fluorescence Spectrometer

RoHS Six-Item Detector – DX-360 Fluorescence Spectrometer

This page provides specifications and FAQs for the DX-360 fluorescence spectrometer. For pricing inquiries, please contact us online or call 19926823034!

Learn more+

RoHS Six-Item Detector – DX-360 Fluorescence Spectrometer

RoHS 2.0 Pyrolysis Gas Chromatograph PY-DP8060

This page provides specifications for the RoHS 2.0 pyrolysis gas chromatograph PY-DP8060, along with FAQs and other information. For a quote, please contact us online or call our hotline at 19926823034!

Learn more+

RoHS 2.0 Pyrolysis Gas Chromatograph PY-DP8060

Halogen detection instrument

This page provides specifications and FAQs for the IDP-6300 halogen detector. For pricing inquiries, please contact us online or call our hotline at 19926823034.

Learn more+

Halogen detection instrument

Frequently Asked Questions

What is RoHS?

RoHS is a mandatory standard established by EU legislation, officially known as the “Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment.” The standard entered into force on July 1, 2006, and primarily aims to regulate the materials and manufacturing processes of electrical and electronic products, thereby promoting human health and environmental protection.

The purpose of this standard is to eliminate six substances—lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers (note: the correct Chinese term for PBDE is “polybrominated diphenyl ethers”; “polybrominated biphenyl ethers” is an incorrect designation)—and specifically stipulates that the cadmium content must not exceed 0.01%.

The latest RoHS Directive has added four new phthalate‑ester testing items: DEHP—di(2‑ethylhexyl) phthalate; BBP—butyl benzyl phthalate; DBP—dibutyl phthalate; and DIBP—diisobutyl phthalate.

What are the limit values for the ten hazardous substances under RoHS?

1. Cadmium: less than 100 ppm.

2. Lead: less than 1000 ppm.

3. Mercury: less than 1000 ppm.

4. Hexavalent chromium: less than 1000 ppm.

5. Polybrominated biphenyls (PBB): less than 1000 ppm.

6. Polybrominated diphenyl ethers (PBDEs): less than 1000 ppm.

7. Di(2-ethylhexyl) phthalate (DEHP): less than 1000 ppm.

8. Butyl benzyl phthalate (BBP): less than 1000 ppm.

9. Dibutyl phthalate (DBP): less than 1000 ppm.

10. Diisobutyl phthalate (DIBP): less than 1000 ppm.

What instruments are typically used for RoHS testing?

The commonly used analytical instrument for RoHS 1.0 is X-ray fluorescence spectroscopy (XRF). XRF analyzers are available in standalone, benchtop, and handheld configurations. Typically, a handheld XRF analyzer is employed first for portable on-site testing, with a focus on components of the product that pose a higher risk of containing restricted substances.

With the introduction of RoHS 2.0, four phthalate esters have been added to the RoHS Directive, necessitating additional testing to determine the levels of these compounds, which are extracted using solvents. The solvent extracts are then analyzed for the presence of phthalates by gas chromatography–mass spectrometry (GC/MS) or gas chromatography with flame ionization detection (GC/FID). Other elements and polybrominated diphenyl ethers/alkylated elastomers are analyzed using comparative methods and GC/MS, respectively.

Do the ten RoHS items require two instruments for testing?

The ten items specified in RoHS require two instruments for testing.
For the ten‑item RoHS testing, two instruments are required to complete the analysis; a single instrument cannot achieve this. Even if one instrument is used to measure heavy metal content, the other must be employed to analyze organic compounds.
X-ray fluorescence spectrometers are used to detect RoHS 1.0, while chromatographs, pyrolyzers, or hyphenated techniques such as GC–MS are employed to analyze the four phthalates specified in RoHS 2.0. At present, no single instrument can independently perform all the tests required for RoHS 2.0.

Can ROHS testing instruments detect metallic elements?

ROHS testing instruments are specialized devices used to detect the presence of hazardous substances in electronic components, household appliances, toys, and other products. These harmful substances can pose long-term risks to both human health and the environment, making the use of ROHS testing equipment of paramount importance.

Regarding whether ROHS testing instruments can detect metallic elements, the answer is yes. This is because ROHS testing covers not only hazardous substances but also the analysis of metallic constituents in compliant products. These metals include lead, cadmium, mercury, and others, which are widely used during the manufacturing process. Although these elements are essential, their excessive use poses significant risks to human health and the environment. Consequently, the advent of ROHS testing instruments has greatly facilitated the detection of metallic elements.

< 12 >