[DePu Instruments] – A manufacturer specializing in testing instruments for RoHS compliance, heavy metals, alloy analysis, halogens, and more!
Product Inquiry:19926823034(WeChat ID is the same)
- All
- Product Management
- News and Information
- Introduction Content
- Corporate outlets
- Frequently Asked Questions
- Corporate Video
- Corporate Portfolio
RoHS 2.0 instrument RoHS 1.0 instrument
Alloy analyzerCoating Analyzer
How do you calibrate an X-ray fluorescence coating thickness gauge?
发布时间: 2022-07-19 10:08
X-ray fluorescence coating thickness gauge It is a method for measuring the thickness of metal coatings. Testing and analytical instruments , during its use, we inevitably encounter certain issues—for example, X-ray fluorescence. Coating thickness gauge As for the issue of calibration, I’ll offer a brief answer to this question today.
I. Zero-Point Calibration
(a) Measurements were taken on the substrate, and the display showed <×.×μm>.
(b) Press the button; the screen displays <0.0>. Calibration is complete, and you may begin measurements.
(c) Repeat steps a and b above to obtain a more accurate zero point and higher measurement accuracy. Once zeroing is complete, measurements can be taken.
II. Two-Point Calibration
1. The single‑specimen method: This calibration technique is suitable for high‑precision measurements and for small workpieces, quenched steels, and alloy steels.
(a) First, perform zeroing (as described above).
(b) Measurements are taken on a standard test piece whose thickness is approximately equal to the expected thickness of the coating being measured, and the display shows <××× μm>.
(c) Use the or key to adjust the reading to the standard value. Calibration is complete; you may now begin measurements.
Note: 1. Even if the displayed result matches the standard slice value, you can still press the or key—e.g., press it once. This applies to all calibration methods.
2. To achieve more accurate two-point calibration, you can repeat steps b and c to enhance calibration precision and minimize unexpected errors.
III. Two-Test-Strip Method
The thicknesses of the two reference plates must differ by at least a factor of three. The coating thickness to be measured should fall between the two calibration values. This method is particularly well suited for rough sandblasted surfaces and high‑precision measurements.
(a) First, calibrate the zero point;
(b) Perform measurements on a thinner standard plate, and use the or keys to adjust the reading until it matches the standard value;
(c) After measuring thick samples, immediately use the or key to correct the readings so that they match the standard values. Calibration is complete; you may now begin measurements.
The above is an overview of how to calibrate an X-ray fluorescence coating thickness gauge. If you have a need for this product, please feel free to contact us online or by phone!
Latest News
Recommended Products
Frequently Asked Questions
What is RoHS?
RoHS is a mandatory standard established by EU legislation, officially known as the “Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment.” The standard entered into force on July 1, 2006, and primarily aims to regulate the materials and manufacturing processes of electrical and electronic products, thereby promoting human health and environmental protection.
The purpose of this standard is to eliminate six substances—lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers (note: the correct Chinese term for PBDE is “polybrominated diphenyl ethers”; “polybrominated biphenyl ethers” is an incorrect designation)—and specifically stipulates that the cadmium content must not exceed 0.01%.
The latest RoHS Directive has added four new phthalate‑ester testing items: DEHP—di(2‑ethylhexyl) phthalate; BBP—butyl benzyl phthalate; DBP—dibutyl phthalate; and DIBP—diisobutyl phthalate.
What are the limit values for the ten hazardous substances under RoHS?
1. Cadmium: less than 100 ppm.
2. Lead: less than 1000 ppm.
3. Mercury: less than 1000 ppm.
4. Hexavalent chromium: less than 1000 ppm.
5. Polybrominated biphenyls (PBB): less than 1000 ppm.
6. Polybrominated diphenyl ethers (PBDEs): less than 1000 ppm.
7. Di(2-ethylhexyl) phthalate (DEHP): less than 1000 ppm.
8. Butyl benzyl phthalate (BBP): less than 1000 ppm.
9. Dibutyl phthalate (DBP): less than 1000 ppm.
10. Diisobutyl phthalate (DIBP): less than 1000 ppm.
What instruments are typically used for RoHS testing?
The commonly used analytical instrument for RoHS 1.0 is X-ray fluorescence spectroscopy (XRF). XRF analyzers are available in standalone, benchtop, and handheld configurations. Typically, a handheld XRF analyzer is employed first for portable on-site testing, with a focus on components of the product that pose a higher risk of containing restricted substances.
With the introduction of RoHS 2.0, four phthalate esters have been added to the RoHS Directive, necessitating additional testing to determine the levels of these compounds, which are extracted using solvents. The solvent extracts are then analyzed for the presence of phthalates by gas chromatography–mass spectrometry (GC/MS) or gas chromatography with flame ionization detection (GC/FID). Other elements and polybrominated diphenyl ethers/alkylated elastomers are analyzed using comparative methods and GC/MS, respectively.
Do the ten RoHS items require two instruments for testing?
The ten items specified in RoHS require two instruments for testing.
For the ten‑item RoHS testing, two instruments are required to complete the analysis; a single instrument cannot achieve this. Even if one instrument is used to measure heavy metal content, the other must be employed to analyze organic compounds.
X-ray fluorescence spectrometers are used to detect RoHS 1.0, while chromatographs, pyrolyzers, or hyphenated techniques such as GC–MS are employed to analyze the four phthalates specified in RoHS 2.0. At present, no single instrument can independently perform all the tests required for RoHS 2.0.
Can ROHS testing instruments detect metallic elements?
ROHS testing instruments are specialized devices used to detect the presence of hazardous substances in electronic components, household appliances, toys, and other products. These harmful substances can pose long-term risks to both human health and the environment, making the use of ROHS testing equipment of paramount importance.
Regarding whether ROHS testing instruments can detect metallic elements, the answer is yes. This is because ROHS testing covers not only hazardous substances but also the analysis of metallic constituents in compliant products. These metals include lead, cadmium, mercury, and others, which are widely used during the manufacturing process. Although these elements are essential, their excessive use poses significant risks to human health and the environment. Consequently, the advent of ROHS testing instruments has greatly facilitated the detection of metallic elements.
