[DePu Instruments] – A manufacturer specializing in testing instruments for RoHS compliance, heavy metals, alloy analysis, halogens, and more!
Product Inquiry:19926823034(WeChat ID is the same)
- All
- Product Management
- News and Information
- Introduction Content
- Corporate outlets
- Frequently Asked Questions
- Corporate Video
- Corporate Portfolio
RoHS 2.0 instrument RoHS 1.0 instrument
Alloy analyzerCoating Analyzer
Precautions for Using a Halogen Moisture Analyzer!
分类: News Center
发布时间: 2022-06-17 11:09
Halogen Moisture Analyzer It is a new type of instrument for rapid moisture analysis. During its use, various situations may arise; to avoid unnecessary issues, it is essential to understand the precautions for operating a halogen moisture analyzer. Based on our compilation, the key precautions for using a halogen moisture analyzer can be summarized as follows:

1. The halogen moisture analyzer is intended for measuring the moisture content of samples; any other use may result in personal injury and damage to the instrument.
2. Please read the instruction manual carefully before use, and do not operate under conditions that do not meet the specified requirements.
3. The halogen rapid moisture analyzer is intended for use only by trained professionals who are familiar with the properties of the samples.
4. The halogen rapid moisture analyzer is powered by a three‑prong grounded outlet. Do not disconnect the instrument’s grounding wire or use a power source with inadequate grounding.
5. Sufficient clearance should be provided around the instrument to prevent heat buildup and overheating.
6. As the area surrounding the instrument’s heating unit becomes hot, do not place flammable materials near the instrument.
7. After testing, since the sample itself, the heating device, and its container remain very hot, exercise caution when removing the sample.
8. During the heating and drying process, the temperature of the annular heating element can reach 400°C. Therefore, do not open or touch the heating unit. If you need to open it, disconnect the power supply and wait for it to cool completely.
9. Exercise particular caution when handling flammable or combustible materials, substrates containing solvents, or substrates that release flammable and explosive gases upon heating, as these samples may pose health hazards or damage equipment. Therefore, when measuring such samples, the heating temperature should be kept sufficiently low to prevent flame formation or the generation of explosive atmospheres, and appropriate protective gear, such as safety goggles, should be worn. If the combustibility of the sample is uncertain, use the smallest possible quantity for testing. In such cases, the instrument should be supervised by a designated operator, and, just in case, conduct your own risk assessment prior to the experiment.
10. For substrates containing toxic elements, such materials may only be heated and dried under well-ventilated conditions.
11. Substrates that generate corrosive vapors during heating and drying. When measuring samples of such substrates, it is recommended to reduce the sample weight, as the vapors may condense on the cooler housing and cause corrosion.
Having reviewed the precautions for using a halogen moisture analyzer, you can be confident that the likelihood of encountering issues during operation will be significantly reduced. After all, regardless of the instrument you’re using, it’s always best to familiarize yourself with its safety guidelines and operating instructions.
Latest News
Recommended Products
Frequently Asked Questions
What is RoHS?
RoHS is a mandatory standard established by EU legislation, officially known as the “Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment.” The standard entered into force on July 1, 2006, and primarily aims to regulate the materials and manufacturing processes of electrical and electronic products, thereby promoting human health and environmental protection.
The purpose of this standard is to eliminate six substances—lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers (note: the correct Chinese term for PBDE is “polybrominated diphenyl ethers”; “polybrominated biphenyl ethers” is an incorrect designation)—and specifically stipulates that the cadmium content must not exceed 0.01%.
The latest RoHS Directive has added four new phthalate‑ester testing items: DEHP—di(2‑ethylhexyl) phthalate; BBP—butyl benzyl phthalate; DBP—dibutyl phthalate; and DIBP—diisobutyl phthalate.
What are the limit values for the ten hazardous substances under RoHS?
1. Cadmium: less than 100 ppm.
2. Lead: less than 1000 ppm.
3. Mercury: less than 1000 ppm.
4. Hexavalent chromium: less than 1000 ppm.
5. Polybrominated biphenyls (PBB): less than 1000 ppm.
6. Polybrominated diphenyl ethers (PBDEs): less than 1000 ppm.
7. Di(2-ethylhexyl) phthalate (DEHP): less than 1000 ppm.
8. Butyl benzyl phthalate (BBP): less than 1000 ppm.
9. Dibutyl phthalate (DBP): less than 1000 ppm.
10. Diisobutyl phthalate (DIBP): less than 1000 ppm.
What instruments are typically used for RoHS testing?
The commonly used analytical instrument for RoHS 1.0 is X-ray fluorescence spectroscopy (XRF). XRF analyzers are available in standalone, benchtop, and handheld configurations. Typically, a handheld XRF analyzer is employed first for portable on-site testing, with a focus on components of the product that pose a higher risk of containing restricted substances.
With the introduction of RoHS 2.0, four phthalate esters have been added to the RoHS Directive, necessitating additional testing to determine the levels of these compounds, which are extracted using solvents. The solvent extracts are then analyzed for the presence of phthalates by gas chromatography–mass spectrometry (GC/MS) or gas chromatography with flame ionization detection (GC/FID). Other elements and polybrominated diphenyl ethers/alkylated elastomers are analyzed using comparative methods and GC/MS, respectively.
Do the ten RoHS items require two instruments for testing?
The ten items specified in RoHS require two instruments for testing.
For the ten‑item RoHS testing, two instruments are required to complete the analysis; a single instrument cannot achieve this. Even if one instrument is used to measure heavy metal content, the other must be employed to analyze organic compounds.
X-ray fluorescence spectrometers are used to detect RoHS 1.0, while chromatographs, pyrolyzers, or hyphenated techniques such as GC–MS are employed to analyze the four phthalates specified in RoHS 2.0. At present, no single instrument can independently perform all the tests required for RoHS 2.0.
Can ROHS testing instruments detect metallic elements?
ROHS testing instruments are specialized devices used to detect the presence of hazardous substances in electronic components, household appliances, toys, and other products. These harmful substances can pose long-term risks to both human health and the environment, making the use of ROHS testing equipment of paramount importance.
Regarding whether ROHS testing instruments can detect metallic elements, the answer is yes. This is because ROHS testing covers not only hazardous substances but also the analysis of metallic constituents in compliant products. These metals include lead, cadmium, mercury, and others, which are widely used during the manufacturing process. Although these elements are essential, their excessive use poses significant risks to human health and the environment. Consequently, the advent of ROHS testing instruments has greatly facilitated the detection of metallic elements.
